|
backwoods boy
|
 |
« on: January 27, 2008, 07:41:55 PM » |
|
i forgot to mark top or bottom on my driveshaft and am not sure wich way to put it in what will happen if i put it in 180' the wrong way its the rear shaft on an 88 fullsize blazer
|
|
|
|
|
Logged
|
NObama08 '' nigga please its the WHITE house''
LIVE FAST-PLAY HARD-DIE LAUGHING
|
|
|
|
Chillinthemost
|
|
« Reply #1 on: January 27, 2008, 07:54:21 PM » |
|
it will be fine
|
|
|
|
|
Logged
|
YFZ FTR B-Open #12
Chillin Jr. FTR Super Pee A #12
|
|
|
|
crom A zone
|
|
« Reply #2 on: January 27, 2008, 08:26:49 PM » |
|
look at the angle if u put it in backwords will be to steep of an angle of rear end and bind yr u joints check before bolt it on bigger u joint goes towrds the rear end
|
|
|
|
|
Logged
|
2008 brute force 750
30inch itp mulite xxl on ss108s
rad reloated and mimb snorkles
gold/red epi clutch springs
hl springs and extream 2inch lift
|
|
|
|
Chillinthemost
|
|
« Reply #3 on: January 27, 2008, 08:31:44 PM » |
|
look at the angle if u put it in backwords will be to steep of an angle of rear end and bind yr u joints check before bolt it on bigger u joint goes towrds the rear end
If I understand you right, you think he means front or back. His driveshaft will have a slip yoke on the tranny side and cant go but one way. I'm assuming that he unbolted it from the rear end and is worried about how to bolt it back to the diff., if thats the case then just bolt it up and go. |
|
|
|
|
Logged
|
YFZ FTR B-Open #12
Chillin Jr. FTR Super Pee A #12
|
|
|
|
crom A zone
|
|
« Reply #4 on: January 27, 2008, 10:23:42 PM » |
|
if its 4x4 they bolt on both sides an are 2 diff size u joints smaller u joint gos in the front bigger in the rear there is not a ibg size diff but it will keep snapping the u joint if put in wronge
|
|
|
|
|
Logged
|
2008 brute force 750
30inch itp mulite xxl on ss108s
rad reloated and mimb snorkles
gold/red epi clutch springs
hl springs and extream 2inch lift
|
|
|
|
Chillinthemost
|
|
« Reply #5 on: January 27, 2008, 10:55:17 PM » |
|
if its 4x4 they bolt on both sides an are 2 diff size u joints smaller u joint gos in the front bigger in the rear there is not a ibg size diff but it will keep snapping the u joint if put in wronge
Not going to argue with you, being that you are 4X4Matt you must know it all. |
|
|
|
|
Logged
|
YFZ FTR B-Open #12
Chillin Jr. FTR Super Pee A #12
|
|
|
|
backwoods boy
|
|
« Reply #6 on: January 28, 2008, 09:27:35 AM » |
|
no i know wich is front and back but im worried about top and bottom it can goin in 2 different ways like 180' upside down
|
|
|
|
|
Logged
|
NObama08 '' nigga please its the WHITE house''
LIVE FAST-PLAY HARD-DIE LAUGHING
|
|
|
|
TRX450R_Racer
|
|
« Reply #7 on: January 28, 2008, 10:10:29 AM » |
|
I agree with Chillin, bolt it up and go.
|
|
|
|
|
Logged
|
Member of South East Florida Trail Riders
Life's to short, wear a helmet.
Dress for the crash, not for the ride.
Ripped off by Brandon George.
|
|
|
|
Anoriginal
Guest
|
|
« Reply #8 on: January 28, 2008, 10:13:22 AM » |
|
Bolt it up and go. You'll be just fine.
|
|
|
|
|
Logged
|
|
|
|
|
Chuck_Norris
Guest
|
|
« Reply #9 on: January 28, 2008, 06:07:44 PM » |
|
If it breaks then you didn't put it in right
|
|
|
|
|
Logged
|
|
|
|
|
crom A zone
|
|
« Reply #10 on: January 29, 2008, 11:33:45 AM » |
|
no it does not matter top and bottom its all the same
|
|
|
|
|
Logged
|
2008 brute force 750
30inch itp mulite xxl on ss108s
rad reloated and mimb snorkles
gold/red epi clutch springs
hl springs and extream 2inch lift
|
|
|
|
gtnwood
|
|
« Reply #11 on: January 29, 2008, 09:34:08 PM » |
|
If it breaks then you didn't put it in right
 |
|
|
|
|
Logged
|
'Political Correctness is a doctrine, fostered by a delusional, illogical minority, and
rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition
that it is entirely possible to pick up a turd by the clean end.'
(From a Texas A&M student)
2005 Kodiak 450, 26" 589s
|
|
|
|
