Home ATV Florida Forum ATV Florida Where to Ride? ATV Florida Links Advertise


Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
 
   Home   Help Search Calendar Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Best Chain Lube?  (Read 9699 times)
eric
Supreme Member
*****
Offline Offline

Location: Sanford

Posts: 1348



View Profile

Ignore
« on: March 07, 2005, 10:57:55 PM »

Wondering if anyone has found a chain lube works good and isn't messy. Maxima makes a "Crystal Clear Chain Guard" and Champion a "white lithium spray grease" anyone tried those? The one I currently use seems to stick to the quad and is hard to clean off.
Logged
Old_School
Supreme Member
*****
Offline Offline

Location: Tampa

Posts: 597


It ain't fast without mixed gas....


View Profile

Ignore
« Reply #1 on: March 08, 2005, 06:08:46 AM »

Me personally I every once and awhile I use any white lithium grease but after I ride I clean the bike then spray wd40 on the chain and roll the bike back and forth a few times and put the bike up. It gets the left over water out and if there's some left it gets diluted(sp?) with the wd40.  -Mark
Logged

90' LT500R Quadzilla
Breathing fire and crushing cities

92' LT250R Quadracer
Some stuff done. 75+mph (Sold)

"When this baby hits 88 mph, you're gonna see some serious $%#!" - Christopher Lloyd
stump66
Supreme Member
*****
Offline Offline

Location: Central Polk

Posts: 786


Quads we ride by God we abide


View Profile

Ignore
« Reply #2 on: March 08, 2005, 04:15:23 PM »

I use PJ's I think is the brand but it does sling all over but I pressure wash after every ride and do the chain area well so its fresh the next time without all the sand and buildup.
Logged

GOD PUT ME HERE TO ACCOMPLISH CERTAIN THINGS, I'M SO FAR BEHIND I'LL LIVE FOREVER!!!! 
AND ITS NEVER!!!!
TOO LATE TO START!!!!
Mars
Supreme Member
*****
Offline Offline

Location: Naples

Posts: 543


When I feel athletic, I go to a sports bar.


View Profile

Ignore
« Reply #3 on: March 08, 2005, 06:42:40 PM »

Bell-Ray "super clean" chain lube.
Logged

04 Z400
99 Foreman 450s, AKA The Pig.
Da_Mtg_Man
extraordinaire
Supreme Member
*****
Offline Offline

Location: far far away

Posts: 7463


View Profile

Ignore
« Reply #4 on: March 08, 2005, 06:43:28 PM »

Quote
Bell-Ray "super clean" chain lube.


What he said
Logged

FLORIDA MUD RIDER
jaxraptor
Junior Member
**
Offline Offline

Location: jax

Posts: 75


Finally, ATVFlorida.com is here!


View Profile

Ignore
« Reply #5 on: March 13, 2005, 06:22:45 PM »

WD40!!!  Use it on all my bike, motorcyle and ATV.  Can't live without it!  "It does not harm the o-rings in the chain!
Logged
VForce700
Guest

« Reply #6 on: March 14, 2005, 07:07:37 PM »

Quote
WD40!!!  Use it on all my bike, motorcyle and ATV.  Can't live without it!  "It does not harm the o-rings in the chain!


same here. I use wd40 on the race bikes when I help out a friend of mine. we never use any chain lube. I use marval mystery oil for the cables as well after washing to make sure all is good when ready
Logged
dreth
Guest

« Reply #7 on: March 16, 2005, 06:13:59 PM »

i prefer maxima chain wax. it sticks to the chain well .
Logged
eric
Supreme Member
*****
Offline Offline

Location: Sanford

Posts: 1348



View Profile

Ignore
« Reply #8 on: March 16, 2005, 10:27:26 PM »

Here is an interesting article http://www.motorcycle.com/mo/mcdirt/trailrider/toolbox8.html

"Naturally, the best way to avoid chain and chain related failures is through regular inspection, adjustment and maintenance. Water, mud, and the like play havoc on equipment, and chain is no exception. The steady diet of mud and water that we typically see stresses the drive chain considerably more that those bikes ridden in controlled and/or dry climates. No doubt things are better than ever with the advent of o-ring chains, significantly reducing adjustment and maintenance needs. However, not all riders opt for o-ring chains, and even o-ring chains will last longer when treated right. Chain maintenance basically boils down to cleaning, lubricating, tightening, alignment and replacement. Accumulated dirt, old lube, crud and corrosion on your chain not only sows the seeds of wear but causes more power robbing friction as well. The best way to rid your chain of these contaminants is a thorough cleaning. The most thorough method of cleaning is accomplished by removing the chain from the bike and soaking it in solvent, like kerosene or diesel fuel. This works wonders for non o-ring chains, but for o-rings, watch out. After a long soak, the solvents can get inside of the o-rings and destroy whatever lubricant remains, while the o-rings can confound your attempts to re-lubricate the chain. Best to just brush off an o-ring chain with a stiff bristle brush, or at most wipe it down with a solvent-soaked rag.

If your chain wasn't too dirty and you opt for cleaning while washing the rest of your bike, be sure to lube your chain before the washing. Washing an unlubed chain allows water to creep and settle in between the various rollers, bushings and pins. If you lube your chain afterward, the lube has the tendency to "seal in" the water, further promoting corrosion. Speaking of lubrication, the only thorough way to lubricate a chain is through immersion. Before o-ring chains, astute riders used to remove their chain after every ride and soak it in a pan of oil for several days. This allowed the oil lubricant to completely flow in between the chain rollers, pins, and bushings. With the advent of o-ring chains, a couple of things happened. First, many o-ring chain manufacturers used to claim that they never needed lubrication. This just isn't true. While the o-rings seal the pin/bushing junction, they do nothing for the chain rollers. O-ring chain rollers still require regular lubrication for this reason, and to ward off corrosion as well. Another rub with o-ring chains is that not only do they seal in whatever lubricant was applied at the factory, but seal out any attempts to relubricate the bearing surfaces afterward. In spite of this, the immersion process will still provide superior lubricant coverage between the chain rollers and bushings, and perhaps seep past more than a few loose o-rings as well.

Spray on lubricants are by far the most popular these days, offering several distinctly different options. They include silicon based sprays, WD40-type cleaners/lubricants, traditional oil based chain lubes, and the new spray on chain wax marketed by Maxima. Opinions regarding the merit of any of these lubes vary greatly, however, we've tried them all and offer the following insight based upon those experiences. Silicon based sprays, TFF, WD40 and CRC type cleaners/lubricants became popular with the advent of o-ring chains. The theory went that since the o-ring chains are lubed at the factory, all that was really needed was a coating to repel dirt and impede corrosion. Silicon base sprays are good at that, providing some lubrication for the o-rings themselves as well. Problem is though that while o-rings seal the pin/bushing junction, the chain rollers themselves remain unsealed and thus require lubrication. The other sprays like WD40 and CRC perform along the same lines, except that these sprays have solvents as well as lubricants and can be helpful removing dirt and old lubricants. The bottom line, however is that chain lubed with these space-age sprays has the tendency to wear out chain rollers, as the rollers never get sufficient lubrication.

Traditional chain lubes are essentially oils with additives to make them stickier, preventing the lubricant from flying off during use. They can provide excellent lubrication of all chain moving components for both standard and o-ring chains. The catch with traditional chain lubes is that not only do they stick to the chains moving parts, but succeed in picking up and capturing dirt, dust and sand at an alarming rate. This turns your chain lube into an abrasive mixture of chain lube and crud not unlike valve grinding compound. Regular chain cleaning can combat this scenario, however removing dried chain lube can be among the toughest bike cleaning tasks. The newest and perhaps most innovative chain lubrication is chain wax. Chain waxes provide a thick water and corrosion blocking coating on the chain and within the various moving parts. The kick with chain waxes is that once dry (after a few minutes) they're non-sticky to the touch and therefore don't attract dirt like traditional chain lubes. To give you some idea of our preferences, I typically use traditional chain lubes on our test bikes and save the coveted chain wax for my personal scoots. Enough said."
Logged
dreth
Guest

« Reply #9 on: March 17, 2005, 07:25:54 PM »

geuss i use the right thing Wink
Logged
PerformanceATV
Newbie
*
Offline Offline

Location: i|U

Posts: 6


Finally, ATVFlorida.com is here!


View Profile

Ignore
« Reply #10 on: March 21, 2005, 06:15:38 AM »

Maxima chain wax, but you must follow the directions  clean chain ,warm up chain, spray on and let dry for 15 min. won't fling off . Works great try it
Logged
big-daddy
Defender of the secret society!
Supreme Member
*****
Offline Offline

Location: Miami

Posts: 5822


Home of the Brave


View Profile

Ignore
« Reply #11 on: March 22, 2005, 11:15:14 AM »

Quote
Maxima chain wax, but you must follow the directions  clean chain ,warm up chain, spray on and let dry for 15 min. won't fling off . Works great try it


I second that. read direction on the can. Maxima chain wax on a clean chain. Grin
« Last Edit: March 22, 2005, 11:15:43 AM by hell-blaster » Logged

I wonder if we can get Cheney to take Obama hunting?
1985 CJ7 Swamp Buggy named Swamp Thing
2001 Yamaha Wolverine 4x4
2005 Kodiak 450 4x4
2007 F150 Super Crew FX4
Proud RR and FMR member
NRA Life Time member
YFZ450AndyH
Guest

« Reply #12 on: March 31, 2005, 08:59:04 AM »

What is the best way to clean the chain before waxing it?
Logged
eric
Supreme Member
*****
Offline Offline

Location: Sanford

Posts: 1348



View Profile

Ignore
« Reply #13 on: March 31, 2005, 07:31:33 PM »

Quote
What is the best way to clean the chain before waxing it?


Kerosene is what my owners manual recommends but I guess you would have to take it off to do that. You going to Scrub Saturday Andy?
Logged
YFZ450AndyH
Guest

« Reply #14 on: March 31, 2005, 09:04:16 PM »

Hey Eric, Im working this weekend.  So the only scrub I will see is people I have to deal with, lol.  I cant wait to get the quad out for a real ride.  
Logged
Axo
Junior Member
**
Offline Offline

Location: n|U

Posts: 76


Finally, ATVFlorida.com is here!


View Profile

Ignore
« Reply #15 on: April 08, 2005, 08:01:34 AM »

WD40 and then Maxima chain wax  Grin
Logged

2003 Raptor 660, Red/Blk, White Bros R4, Jet Kit, Pro Design Pro flow Kit, IMS Pegs,IMS Heel guards,AC Nerfs, AC Front Bumper, 5" rear wheel spacers, 3" front wheel spacers.
HUGGYJD
Newbie
*
Offline Offline

Location: l|U

Posts: 14


Finally, ATVFlorida.com is here!


View Profile

Ignore
« Reply #16 on: April 08, 2005, 08:19:51 PM »

I have always used Maxima chain wax with good results.
Logged
CAOSPOP
Guest

« Reply #17 on: April 09, 2005, 06:41:34 AM »

Pressure wash then daus(sp?) with WD 40
Logged
400exRacer77
Senior Member
****
Offline Offline

Location: o|U

Posts: 296


# 71


View Profile

Ignore
« Reply #18 on: April 10, 2005, 05:48:47 PM »

WD40 every time i stop ridin, have had my chain and sprokets for a year on a MX BIKE!!!! ..... if you do it the right way nothin will ever mess up
Logged

2000-03 CRF450EX ..... Houser +3 LT a-arms and +1.25 swingarm, Custom Axis fully adjustable suspension front and rear, Walsh radiator, Douglas wheels, CRF450 motor, not quite done yet though......
Yamaha72
Supreme Member
*****
Offline Offline

Location: Davie/Orlando

Posts: 890



View Profile

Ignore
« Reply #19 on: May 16, 2005, 08:44:16 PM »

Maxima Chain wax here or PJ1 Bluelabel chainlube.
Logged

2003 Yamaha Raptor 660

2005 Ford F-150
bigsteve
Full Member
***
Offline Offline

Location: Sarasota

Posts: 113



View Profile

Ignore
« Reply #20 on: May 23, 2005, 11:25:34 PM »

You have to be careful cleaning your chain with high pressure it can force dirt pass O-Ring seals into the pins and have premature wear.Rub down with A well soaked rag with karo. or disael fuel.To remove old lub.Then put new lub on.

Just my 2cents.
Logged

"IT'S OK TO BE CRAZY! JUST DON'T LET IT DRIVE YOU INSANE!
04 CRF 80
05 LTZ 250
05 KFX 100
05 KFX700 (You know GREEN is faster so don't ask!)
03 Mojave
04 CRF 250
07 RMZ 250
05 DRZ 400
Teej
Full Member
***
Offline Offline

Location: North, FL

Posts: 217

Finally, ATVFlorida.com is here!


View Profile

Ignore
« Reply #21 on: July 26, 2005, 07:32:57 PM »

Has anyone used "White Lightening" or "Prims Lube Gel"?

Thanks Teej
Logged

Kawasaki 400 4x4 Prarie, Mine
Polaris 330 Trailboss, Wife's
Honda 250 Recon, Daughters
Kazuma 110 Falcon Mkll, Sons
felix_z-4
Full Member
***
Offline Offline

Location: Orlando

Posts: 229


Finally, ATVFlorida.com is here!


View Profile

Ignore
« Reply #22 on: July 26, 2005, 09:52:47 PM »

Maxima chain wax, very good product..
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Other Florida sites of interest: www.PinballShark.com

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!