in line cooler help?

[MOTOCROSS MAVERICK]

i am going to put a inline cooler on my yfz and i dont know if i should put it on the coolent going in the motor side or going out side?

i am probably going to add a ESR in line water temp guage and my thoughts were to put that on the water coming from the motor to the radiator and the cooler on the other side!  but what do i know!

[TRX450R_Racer]

I would put the one with the guage in the hose you can see and the regular one in the other hose.

[MOTOCROSS MAVERICK]

I would put the one with the guage in the hose you can see and the regular one in the other hose.

on the yfz you can see the hoses on both sides! i was just wondering if it mattered temp wise with the water, i would think would be hotter comming out of the motor than going in! so i didnt know which sides to put which to make any difference!

[backinsaddle]

I don't know about the inline cooler, but I would definitly put the temp guage on the side feeding from the motor back to the radiator...you want to know how hot the motor is running, not how hot the water is before it goes back in the motor.

[Old_School]

Inline coolers help very little but they do help. Using an engine ice type coolant (that's what I use) or something equivalant  with the cooler may drop the temps a few degrees.  The bigger the cooler the better. Look for some that are around 20 fins. That's the biggest I've see.  But make sure you put it where air will have a straight shot at the cooler. That's what makes them work.  -Mark

[backinsaddle]

Now that I think about it some more, the YFZ has an overheating light.  I would think that has to come from a temperature sending unit somewhere on the motor.  Seems to me you could disconnect the light, and use that port/hardware to connect the temp guage?  part #'s 6&7 in the pic below seem to be the temp sending units.  Not sure if it would screw anything else up, but you may be able to tap into those

[attachment deleted by admin]

[Chillinthemost]

The guage is probably not a bad idea. The cooler, I doubt makes enough difference to matter. If you want one though, the guy that was with me on the triZ 3 wheeler (yamahondaman)at sand mountain makes them and a lot of other cool aluminum parts.

[YAMAHONDAMAN]

Them 20 fin ones i think are TOO LONG .. the normall ones i make for the Banshee's are 12 fin and 1.5 Dia., i need to get some 1.75 dia. 12-finned ones made up for the 450's...they would be more better looking and Practical,also they are made for the BIG Hose(.812) unlike the others that fit the .75 lines..i'll try and have some at the next sand mtn.race..
13.00 a-piece or a set for 20.00....

[LE450-RACER#77]

Hey Mav put the esr inline guage on the side coming from the motor & put the cooler on the side coming from the radiator. That way the water is a little cooler before going back into the motor.

[MOTOCROSS MAVERICK]

thanks everybody you all have been big help!

[53yfz450]

i just made 1 in machining class today. it took me like 10 minutes.

[MOTOCROSS MAVERICK]

i just made 1 in machining class today. it took me like 10 minutes.

you are so full of crap!!!!!!! you brag all the the time about you making stuff in your class and i have not seen a thing!

[53yfz450]

oh yeah wait till the next time i see you. i will have one for JP and nothing for you.

[MOTOCROSS MAVERICK]

hahahaha i bet it looks like crap! how about is it colored like mine?

[53yfz450]

no but its polished.

[2006YFZ450]

Well hey I think im going to start making some parts in my Drafting/Engeenering class.  My teacher will let me use his CNC Machine once it gets up and running

[MOTOCROSS MAVERICK]

then it is polished crap!!!!! oh waityou probably bought it from pit posse!

[53yfz450]

yeah ok.

[2006YFZ450]

yeah ok.

I know how it feels when someone doesn't believe you.........



What exaclty are you making agian???     I think I can make the brackets that the rear fenders bolt on to

[YAMAHONDAMAN]

CNC Cooler Program%
:2709
N100G50G0G99G97
T0707M8
S1500M3
X2.05Z-4.235
G1X.760F.004
G0X2.05
Z-4.185
G1X.815
X.760Z-4.235
X-.03F.002
M9
M5
G0Z-4.0
X-2.1
M11
G4P500
G98G1Z.135F55.0
G4P1000
M10
G4P1000
G0Z.2
X3.0Z3.0
T0700
M1
N150G0G99G97
T0101M8
S1500M3
X2.05Z.03
G1X-.06F.012
G0X2.05Z.05
Z.005
G1X-.06
G0X1.77Z.05
G1Z-4.235
X2.05
G0Z.05
X1.5
G1Z-.77
X1.8
G0Z.05
X1.25
G1Z-.77
X1.55
G0Z.05
X1.0
G1Z-.77
X1.6
G0Z.05
X.83
G1Z-.77
X1.03
G0X2.0Z2.0
T0100
M1
N200G50G0
T0202M8
S1500M3
X.875Z0.0
G1X-.03F.006
G0X.760Z.025
G1Z0.0F.002
X.815Z-.055F.003
Z-.773F.006
X1.715
X1.75Z-.7905F.003
Z-4.235F.006
X2.05F.025
G0X6.0Z6.0
T0200
M1
N300G50G0
T0707M8
S1500M3
X1.8Z-1.01
G1X1.400F.003
X1.405
X1.300
X1.305
X1.200
X1.205
X1.100
X1.105
X1.000
X1.005
X.900
X.905
X.815
G4P200
G0X1.8
Z-1.235
G1X1.400
X1.405
X1.300
X1.305
X1.200
X1.205
X1.100
X1.105
X1.100
X1.105
X1.0
X1.005
X.900
X.905
X.815
G4P200
G0X1.8
Z-1.46
G1X1.400
X1.405
X1.300
X1.305
X1.200
X1.205
X1.100
X1.105
X1.0
X.900
X.905
X.815
G4P200
G0X1.8
Z-1.685
G1X1.400
X1.405
X1.300
X1.305
X1.200
X1.205
X1.100
X1.105
X1.0
X1.005
X.900
X.905
X.815
G4P200
G0X1.8
Z-1.91
G1X1.400
X1.405
X1.300
X1.305
X1.200
X1.205
X1.100
X1.105
X1.0
X1.005
X.900
X.905
X.815
G4P200
G0X1.8
Z-2.135
G1X1.400
X1.405
X1.300
X1.305
X1.200
X1.205
X1.100
X1.105
X1.00
X1.005
X.900
X.905
X.815
G4P200
G0X1.8
Z-2.36
G1X1.400
X1.405
X1.300
X1.305
X1.200
X1.205
X1.100
X1.105
X1.0
X1.005
X.900
X.905
X.815
G4P200
G0X1.8
Z-2.585
G1X1.400
X1.405
X1.300
X1.305
X1.200
X1.205
X1.100
X1.105
X1.0
X1.005
X.900
X.905
X.815
G4P200
G0X1.8
Z-2.81
G1X1.400
X1.405
X1.300
X1.305
X1.200
X1.205
X1.100
X1.105
X1.0
X1.005
X.900
X.905
X.815
G4P200
G0X1.8
Z-3.035
G1X1.4F.003
X1.405
X1.3
X1.305
X1.2
X1.205
X1.1
X1.105
X1.0
X1.005
X.9
X.905
X.815
G4P200
G0X1.8
Z-3.26
G1X1.4F.003
X1.405
X1.3
X1.305
X1.2
X1.205
X1.1
X1.105
X1.0
X1.005
X.9
X.905
X.815
G4P200
G0X1.8
Z-3.495
G1X1.4F.003
X1.405
X1.3
X1.305
X1.2
X1.205
X1.1
X1.105
X1.0
X1.005
X.9
X.905
X.815
G4P200
G0X1.8
Z-3.585
G1X.820F.004
G0X1.8
Z-3.685
G1X.820
G0X1.8
Z-3.785
G1X.820
G0X1.8
Z-3.885
G1X.820
G0X1.8
Z-3.985
G1X.820
G0X1.8
Z-4.085
G1X.820
G0X1.8
Z-4.185
G1X.820
G0X2.05
Z-4.235
G1X.820
G0X1.8
Z-3.4675
S350
G1X1.75F.004
X1.705Z-3.485F.002
X.822F.006
X.815F.004
S650
G1Z-4.235F.004
X.850
G0Z-3.975
G1X.780
G0X1.8
Z-.26
G1X.900F.025
X.780F.004
G0X1.8
X3.0Z3.0
T0700
M1
N400G50G0
T0303M8
S1200M3
X0.0Z.05
G1Z-.07F.002
Z-.06
Z-.125
G0Z7.0
T0300
M1
N500G50G0
T0404M8
S1000M3
X0.0Z.05
G1Z-.200F.005
G0Z.05
Z-.175
G1Z-.400
G0Z.05
Z-.375
G1Z-.600
G0Z.05
Z-.575
G1Z-.800
G0Z.05
Z-.775
G1Z-1.0
G0Z.05
Z-.975
G1Z-1.200
G0Z.05
Z-1.175
G1Z-1.400
G0Z.05
Z-1.375
G1Z-1.600
G0Z.05
Z-1.575
G1Z-1.800
G0Z.05
Z-1.775
G1Z-2.0
G0Z.05
Z-1.975
G1Z-2.200
G0Z.05
Z-2.175
G1Z-2.400
G0Z.05
Z-2.375
G1Z-2.600
G0Z.05
Z-2.575
G1Z-2.800
G0Z.05
Z-2.775
G1Z-3.0
G0Z.05
Z-2.975
G1Z-3.200
G0Z.05
Z-3.175
G1Z-3.400
G0Z.05
Z-3.375
G1Z-3.600
G0Z.05
Z-3.575
G1Z-3.8
G0Z.05
Z-3.775
G1Z-4.0
G0Z.05
Z-3.975
G1Z-4.2
G0Z.05
Z-4.175
G1Z-4.375
G0Z1.0
X5.0
T0400
M0
M99
%

[2006YFZ450]

WOW....Thanks YAMAHONDAMAN

Now that has to be typed in the computer

[YAMAHONDAMAN]

at work i Grabbed the Program from "my files" and Posted em on here ..the cut off tool "#7" is .16 wide...tool #1 is the .03 Rougher and the #2 Tool is the .015 finisher..#3 is the 5/8's spot and #4 is the Coolant Fed Drill...CNC Machining ,,,,  the 12' Bar Doesn't last long !!!   see yall later !!!!!

[attachment deleted by admin]

[Smoknbanshee]

at work i Grabbed the Program from "my files" and Posted em on here ..the cut off tool "#7" is .16 wide...tool #1 is the .03 Rougher and the #2 Tool is the .015 finisher..#3 is the 5/8's spot and #4 is the Coolant Fed Drill...CNC Machining ,,,,  the 12' Bar Doesn't last long !!!   see yall later !!!!!

these boys still can't make struts like you.....

GET IT RAG///

[YAMAHONDAMAN]

Thanks to YOU for the IDEA !!!!     

[Chillinthemost]

Thanks for the #s Ronnie, I just programed them into my cordless drill and cranked a coulple of coolers out . Git it RAG.