OK so here's the rest of the story, the "addition lands" as this is called, was open to public with untethered orv access throughout the area. Once this was taken over by the park service they closed it until they could do a GMP(General Management Plan) and has since been closed. All of the proposals are bad because they all include some kind of WILDERNESS DESIGNATION. When congress passed the law that allowed this, they never mentioned WILDERNESS, instead traditional uses were to continue and have not. I will be submitting my comments asking that they have a proposal with no wilderness and ORV activity. Either way please comment on what you believe will be best....Thxs Rick

Rick you know more about this location than I.  Is this the old Bad Luck area?

Holy pupu thats a funny story, glad to see other people have the same problems as I do after a few adult beverages and here I thought it was just me.

We know your "Special" but not that special.  LOL   

  he sure is special   dont worry buddy me u and art all know them adult beverages can have crazy affects 

Art knows of these soda pops ALL to well!!!!  LMAO

Wacker,

     I know the people who own the Yacht Club through some other friends.  The place is AWESOME!!!!  All I can say is drive through ATV and Buggy wash down.  Great for those Hot days with the ladies...

The best part of Fish ran down his mama's leg.........

[Never argue with an Idiot. They drag you down to their level, and then beat you with experience!]

Freak,

Never argue with an Idiot. They drag you down to their level, and then beat you with experience!

Damn I forgot I still had that in my sig!!!  But your right.. I'm out.  Going to load up the quyad and do some riding.  Found a sweet little spout around the corner from my house!!!   

Its a timing issue, as was already said if its blowing the carb off its sparking while the intake valves are open.  Check the timing chain.

I thought you were done with the political posts?

I guess you don't know how to man up...  Did you leave your big girl panties at your boyfriends house out there in NV?  If you can find them, put them on and STFU!!! 

you would be off to a great start by deleting some of you topics

Good idea, I removed one topic,  now I will need some other topics removed.  Challenge for Fishaholic, Which president is really to blame for the economy and A must read for all gun owners.  For each one of these removed I will remove one of mine.  If all 3 are removed I will remove all of mine.

Fish     Cut the elementary school ground sh!t and remove your posts if you want.  No the if this ones does this I will do this.  Freakin man up and put your big girl panties on or just STFU.  Its sh!t like this as to why I'm not here much anymore.

Ricky,

  All I can say is NOBAMA!!!

what are you trying to build ?  from the drawing it looks like a A-arm with a wheel

Looks like a bumper...   

its called a yoke, the yoke is bolted to your pinion gear on the rear end. the yoke is what the u joint is clamped on to. it sounds liek you have a solid yoke on the trans, meaning you have a slip dirveshaft. its not "adjusting", it has to slip to compensate for suspension travel. i think all that they are saying is to make sure you mark what end goes toward the front and what end is toward the back becasue of the fact that you have a solid yoke on both the trans and the rear end, you can mix them up. if you had a slip yoke on the trans (like most trucks) you couldn't mix them up.

Npe mark it so they align back up cause if you put it in 180 degrees off you might have one hell of a wobble since the shaft is not balanced.  Most shafts are slip shafts and bolt or slide into the tranny/x-fer case.  The Pinion end is usually held on with the saddels.  mark the right side of the shaft to the right side of the yoke and tranny and also the pinion side of the shaft and the pinion.

You want to make sure it goes back in EXACTLY how it came out.

Hose it down with PB Blaster or Auto Tranny fluid and let it sit for a day or so if you can.  Both of these will eat the rust away and make it easier.

Take the clips out of each side then using a vise or c-clamp push them out.  Now you will want to use 2 sockets a big one that the cap will fit into and a smaller one that is just smaller than the cap.  Use the smaller socket to push the u-joint out and into the larger one. 

If this does not work you might need to take the drive shaft off and use a press.  Before you take the drive shaft off mark it on both ends so it goes back in the same way and is balanced.

Thanks everyone, its something I needed to do.


Mike its between Port Charlotte and North Ft Myers

I signed the papers today!!!!!   

Haven't been around much lately, having way to much fun doing other things and haven't had much time to sit in front of a computer.

Yes there is a known issue with SP3.  It has to do with intel chipset configurations being loaded onto a non-intel based computer (AMD).

The system will just reboot, or not boot up at all.

It also strips out the Authentication tab for the 802.1x (DOT1X security) on the NIC card.  Those of us who run Computer based certificate security on our networks this is a MAJOR issue.  The Computer cert can no longer be bound to the user it has to be bound to the NIC card and this defeats the security .  To work around this we had to go to a user based certificate for security.

Polaris also have a wire or part that is known for breaking which will prevent it from starting.

Outlaws are axle breakers.

Check out the mudbugs, they are a great cheap mud tire.

WOW  $1300 the bilstines for my truck didn't cost that much!!!!!

Scott I will agree with you.  I was VERY suprised it didn't get called as tripping.  But it does look like he might have been blocked down a bit.


BTW what do you call a Dallas Cowboys Huddle???























Drug Ring....   HAHAHAHAHAHA     

[plug]

and don't forget to plug the carb drain tube that comes out of the bottom of your carb. It also serves as a vent when the drain screw is closed. And also re run your differential and brake vents as well, either run them up alongside of your snorkel, or up into your headlight pod.

Also don't forget the fan motor vent if you have a fan

Pats and Packers in the SB and the Pats will come out on top.     

Could be a bad spark plug, plug wire,. or coil pack

Great gift! We got ours last year.......! Get ready to start paying 30-40 extra dollars a month on FPL bill due to the power behind this TV. How big is yours? Ours is 42'". Perfect for the whole family.

 yea its a 42".  I currently have and older 36" Sony Wega (also sucks power) so I shouldn't see to much of a difference. 

I also got this HD plasma TV and HD Sat. receiver for christmas

Happy Birthday Jeff!!!!   Enjoy your 21st  lol